We have unearthed this great article relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the internet and figured it made good sense to talk about it with you in this article.
Mounting a bathtub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old bath tub with a brand-new one is additionally a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open a wall surface to remove the old tub as well as place the new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about employing one before you begin. Chances are you may require a specialist plumber to make tube links.
This short article will aid you set up a new bathtub in your bathroom if you have actually already bought a brand-new tub and also don't require to change the setup of your previous water system pipelines.
Your devices and product checklist should make up the following:
Preparing for the Setup
To start with, the sustaining structure provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you utilize all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the water. After doing so, activate the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wood boards are valuable in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub until the spirit level reads level.
To install taps, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water system and check all joints and also brand-new pipework for leakages as well as tighten them if required. Load the bath tub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bath tub should wait until the tub has actually been made use of at least once as this will resolve it into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will need a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers are in area between the tap and the sink. Safeguard the faucet in place with the manufacturer supplied backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The former kind must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, creating the water to pass through the wall in between the bathroom and also the tiling, resulting in difficulties with wetness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can split fairly early if you do not take into account this motion before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently readily available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try to leave a remark below. We'd be glad to see your opinions about this article. Hoping that you visit us again in the future. Do you know another person who is interested in the niche? Be sure share it. I cherish reading our article about How to Install a Bathtub Yourself.
Excellence in emergency plumbing services.